MAX6649MUA/V+【PDF 5/16 页】IC SENSOR REMOTE SMBUS 8UMAX

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录44

1页 2页 3页 4页 [5页]6页 7页 8页 9页

+145癈 Precision SMBus-Compatible Remote/

Local Sensors with Overtemperature Alarms

Detailed Description

The MAX6646/MAX6647/MAX6649 are temperature sen-

sors designed to work in conjunction with a microproces-

sor or other intelligence in thermostatic, process-control,

or monitoring applications. Communication with the

MAX6646/MAX6647/MAX6649 occurs through the

SMBus-compatible serial interface and dedicated alert

and overtemperature outputs. ALERT asserts if the mea-

sured local or remote temperature is greater than the

software-programmed ALERT high limit or less than the

ALERT low limit in the MAX6649. ALERT also asserts, in

the MAX6649, if the remote-sensing diode pins are short-

ed or unconnected. The overtemperature alarm, OVERT,

asserts if the software-programmed OVERT limit is

exceeded. OVERT can be connected to fans, a system

shutdown, a clock throttle control, or other thermal-man-

agement circuitry.

The MAX6646/MAX6647/MAX6649 convert temperatures

to digital data either at a programmed rate or in single

conversions. Temperature data is represented as 11 bits,

with the LSB equal to 0.125癈. The main temperature

data registers (at addresses 00h and 01h) are 8-bit regis-

ters that represent the data as 8 bits with the full-scale

reading indicating the diode fault status (Table 1). The

remaining 3 bits of temperature data are available in the

extended registers at addresses 11h and 10h (Table 2).

ADC and Multiplexer

The averaging ADC integrates over a 60ms period

(each channel, typically), with excellent noise rejection.

The multiplexer automatically steers bias currents

through the remote and local diodes. The ADC and

associated circuitry measure each diodes forward volt-

age and compute the temperature based on this volt-

age. Both channels are automatically converted once

the conversion process has started, either in free-run-

ning or single-shot mode. If one of the two channels is

not used, the device still performs both measurements,

and the results of the unused channel can be ignored.

If the remote-diode channel is unused, connect DXP to

DXN rather than leaving the inputs open.

Pin Description

NAME

FUNCTION

Supply Voltage Input, 3V to 5.5V. Bypass V

to GND with a 0.1糉 capacitor. A 200 series resistor is

recommended but not required for additional noise filtering.

DXP

Combined Remote-Diode Current Source and A/D Positive Input for Remote-Diode Channel. DO NOT

LEAVE DXP UNCONNECTED; connect DXP to DXN if no remote diode is used. Place a 2200pF

capacitor between DXP and DXN for noise filtering.

DXN

Combined Remote-Diode Current Sink and A/D Negative Input. DXN is internally connected to ground.

OVERT

Overtemperature Alert/Interrupt Output, Open Drain. OVERT is logic low when the temperature is above

the software-programmed threshold.

GND

Ground

ALERT

SMBus Alert (Interrupt) Output, Open Drain. ALERT asserts when temperature exceeds limits (high or

low temperature). ALERT stays asserted until acknowledged by either reading the status register or by

successfully responding to an alert response address, provided that the fault condition no longer

exists. See the ALERT Interrupts section.

SDA

SMBus Serial-Data Input/Output, Open Drain

SCLK

SMBus Serial-Clock Input

TEMP (?/SPAN>C)

DIGITAL OUTPUT

+145

1001 0001

+130

1000 0010

+128

1000 0000

+25

0001 1001

0000 0000

Diode fault

(short or open)

1111 1111

Table 1. Main Temperature Data Register

Format (00h, 01h)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式